【提问】I have a question

jupiter

[첨부] 4628 [/ 첨부]
증분 버튼 질문

위와 같이 늘리거나 줄입니다.


그러나 "증분 조정"
1 씩 늘리거나 줄입니다.

다른 값으로 변경할 수 있습니까? +-10 또는 + -45


그리고 한국에서이 제품을 개발하는 사람이 있습니까?





이미지에서 5를 누릅니다. +5
10을 +10으로 누릅니다.

이 설정이 필요합니다.

나는

jupiter

Add Questions

I want to add a constant to the basic touch or the rerun key code and increase it to the corresponding value.

AHYEAH

Dear customer

To change a different value, you can change the step length  
eg:-45 :  step length: 45
               adjust method: choose  "--"

And could you please let us know your model number.

jupiter

You have modified the question.
Please help me.

AHYEAH

http://inforum.dwin.com.cn:20080 ... amp;_dsign=c7cf9ba3

Maybe you can check the link, use 00B0 order.

solo

The example for Return Key Code, total 4 modes for 0×B0. Mode 0: disable the touch. Mode 1: enable the touch.
1, Turn off one touch, send command: 5A A5 0B 82 00B0 5AA5 0001 0905 0000 [0001 means page 0001, 09 means the 9th touch file on page 0001 (set in development software), 05 means touch control code (check the application guide as following), 0000 means turn off the touch, will be invalid if do gray keying].
2, Enable one touch, send command:  5A A5 0B 82 00B0 5AA5 0001 0905 0001 [0001 means page 0001, 09 means the 9th touch file on page 0001 (set in development software), 05 means touch control code (check the application guide as following), 0001 means turn on the touch, will be invalid if do gray keying].
3, Mode 2 and Mode 3 are used to change the settings of the touch control. I. Read the touch control Setting parameters: 5A A5 0B 82 00B0 5AA5 0000 0105 0002, then send the command 5A A5 04 83 00B4 16, the returned data can refer to the following screenshot; II. Modify the setting parameters of the touch control: 5A A5 2B 82 00B0 5AA5 0000 0105 0003 0000 0032 000B 01A9 005A FF00 FF00 FE05 FE 1430 00 0002 00 00 00 00 00 00 00 00 00 00 00, this command make the key value has been modified successfully.

jupiter

Can you make an example using DGUS Tool V7.388? It's very difficult because it's my first time using it for the first time.

eileen1213

http://inforum.dwin.com.cn:20080/forum.p ... 3D1&_dsign=19c20046      Hello, you can refer to the video of K600+. The basic development is the same, but the variable address range is different. The address range of T5 is 0x1000-0xffff, and that of K600+ is 0x0000-0x6fff.The screen of T5 has no register address, so the system interface variable address can be directly changed. The control address can be used from 1000.T5 screen replaces the CONFIG file of K600+ with the CFG file. The CFG file beyond the green part cannot be configured by itself to avoid misoperation.http://inforum.dwin.com.cn:20080/forum.php?mod=viewthread&tid=1228&extra=page%3D1

• This is the address of DEMO, you can refer to it