【提问】DMG80480C043_02WTC烧录后黑屏

忧郁蓝调

eileen1213 发表于 2021-8-2 11:05
楼主，您的屏是不是新买的，您把DWIN_SET文件夹用这个软件转换一下看下，建议开发用7.620以上版本
...

好的，我试一下，谢谢

忧郁蓝调

luoyangdwin1 发表于 2021-8-2 11:05
楼主用这个软件转换一下DWIN_SET文件夹，应该是内核和软件版本不匹配的问题，后续用上面发您的7.624的开 ...

我直接用DGUS_V7624重新做了一遍，还是黑屏

luoyangdwin1

忧郁蓝调 发表于 2021-8-2 15:20
我直接用DGUS_V7624重新做了一遍，还是黑屏

楼主烧录一下这个内核文件试试，如果还是存在问题可以在QQ搜索4000189008找1007帮您看一下。

rm191

luoyangdwin1 发表于 2021-8-2 15:59
楼主烧录一下这个内核文件试试，如果还是存在问题可以在QQ搜索4000189008找1007帮您看一下。

...

how can i burn kernel file ? with which software ?

zhuliuqin123

Hello, put it directly into the DWIN_SET folder and use the SD card to go in;

pmatsol58

Hi, could I use the DMG80480C043_02WTC.zip file to recover a DMG80480C043-02WTRZ07 display using a PGT05?

其乐融融

pmatsol58 发表于 2021-11-10 11:02
Hi, could I use the DMG80480C043_02WTC.zip file to recover a DMG80480C043-02WTRZ07 display using a P ...

You can recover it by SD card，not PGT05.

pmatsol58

My display will not read the SD card and no serial connection either, screen is blank hence I need to use a PGT05 to recover the display. I need the factory default files for the display.

zzs999k

pmatsol58 发表于 2021-11-11 06:44
My display will not read the SD card and no serial connection either, screen is blank hence I need t ...

First:
1.Set the UI core file to be burned (such as: T5L_UI_Flash整片擦除.BIN ), and Change the name to T5UIC1V10.BIN , put it into the SD card, and insert it into the SD card slot of the writer；
2.Power on the PGT05 writer, wait for about 2 seconds after the update is complete, the CODE light flashes once, and the PRG light turns on.
  The kernel file has been read into the writer, you can cut off the power and pull out the SD.
3. Insert the burner pin into the dedicated burning hole next to the standard screen (usually next to the chip, there are 7 on the T5L screen).
4.Power on again, press the burn key, the code light starts to flash, and about two seconds later, the PRG light is on, that is, the burning is successful;


second:
1.Set the UI core file to be burned (such as: T5L_UI_DGUS2_V43_20211021.BIN), and Change the name to T5UIC1V10.BIN , put it into the SD card, and insert it into the SD card slot of the writer；

2.Power on the PGT05 writer, wait for about 2 seconds after the update is complete, the CODE light flashes once, and the PRG light turns on.
  The kernel file has been read into the writer, you can cut off the power and pull out the SD.
3. Insert the burner pin into the dedicated burning hole next to the standard screen (usually next to the chip, there are 7 on the T5L screen).
4.Power on again, press the burn key, the code light starts to flash, and about two seconds later, the PRG light is on, that is, the burning is successful;


final：
1.Rename "DWIN_SET1" to "DWIN_SET" and then "DWIN_SET "put in the SD card and insert the SD card directly into the screen card slot to burn the project.
2.Apply pressure slightly with the tip of the pen in turn (resistance touch screen pressure sensing to ensure effective operation of the operating contacts). Click "upper left corner, upper right corner, lower right corner and lower left corner" of the touch screen in turn to see the white pixel display of each contact.
3.Rename "DWIN_SET2" to "DWIN_SET" and then "DWIN_SET "put in the SD card and insert the SD card directly into the screen card slot to burn the project.

pmatsol58

Thank you for your instructions, I have now recovered my display.
One point to note is that the two UI core files need to be placed in a DWIN_SET folder on the SD card for the PGT05 to program them properly.